|
SHAFT MOUNTED PROPELLER PROTECTOR AND LINE CUTTERS
|
|
|
NO NEED TO DIVE TO REMOVE LINES, WEED ,PLASTIC OR NETS FROM PROPELLER AND SHAFT
|
|
The Cutter's blades attach to the propeller shaft and cut away dangerous obstructions while the shaft turns.
A fixed blade, which is part of the cutter unit, is mounted in bearings. The rotating cutter, bolted on to the shaft,creates a powerful shearing action as the blades pass each other. A striker plate mounted on the stern gear (strut) locks the fixed cutter, while also allowing the shaft both axial and radial movement.
The simple, trouble free mechanism absorbs all vibrations, noises or rumblings and there is never any wear on the shaft.
The needle sharp teeth extend to the very tips of the blades for maximum cutting power.
Installation is straight forward and does not require removal of the propeller.
To determine the correct Cutter model for your boat please refer to the drawing and table below. If you have insufficient clearance between the propeller and the strut, we can provide spacers that will extend the prop shaft aft by the required amount.
|
|
|
|
SHAFT DRIVE CUTTER SELECTION
|
|
|
|
|
MODEL
|
# BLADES
|
SHAFT DIA
|
HUB DIA(B)
|
BLADE DIA (F)
|
CUTTER WIDTH
|
STRUT DIA(D)
|
MINI- GAP (E)
|
|
G66-2
|
2
|
1" to 1 1/2" (25-35mm) 25mm to 35mm
|
66 mm or 2-1/2"
|
118 mm
|
32 mm
|
50-66 mm
|
38 mm
|
|
G66-3
|
3
|
1" to 11/2"(25-35mm) 25mm to 35mm
|
66 mm or 2-1/2"
|
118mm
|
32mm
|
50-66 mm
|
38mm
|
|
G86-2
|
2
|
1 1/2" to 2"(40-50mm) 40mm to 50 mm
|
86 mm or 3-1/2"
|
152mm
|
38 mm
|
66-86 mm
|
44 mm
|
|
G86-3
|
3
|
1 1/2" to 2"(40-50mm) 40mm to 50 mm
|
86 mm or 3-1/2"
|
152mm
|
38 mm
|
66-86 mm
|
44 mm
|
|
G110-2
|
2
|
2" to 3"(50-75mm) 50mm to 75 mm
|
110 mm or 4-5/16"
|
184mm
|
54mm
|
90-115mm
|
60mm
|
|
G110-3
|
3
|
2" to 3" (50-75mm) 50mm to 75 mm
|
110 mm or 4-5/16"
|
184mm
|
54mm
|
90-115mm
|
60mm
|
|
G110-4
|
4
|
2" to 3" (50-75mm) 50mm to 75 mm
|
110 mm or 4-5/16"
|
184mm
|
54mm
|
90-115mm
|
60mm
|
|
For maximum efficiency, select the Cutter model with the same number of blades as your propeller.
Alternatively, a two blade cutter may be used on a two or four blade propeller, and a three blade cutter may be used on a three or five blade propeller.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
