|
|
|
Outlook Express Setup For Macintosh
|
|
|
|
|
General Mail Client Setup Information
|
|
You will be able to use this information to configure most mail clients.
This information will contain your email address, your POP3 incoming mail server, our SMTP outgoing mail server (you could also use your ISP's outgoing mail server) and email account login name. For security and privacy reasons we will not display your password.
|
|
|
Note: If you use "smtp.eznettools.net" as the outgoing mail server it does require the same authentication as the incoming mail server
|
|
|
Note: Your ISP (internet service provider) might block any SMTP activity that is not theirs. You might have to look up their SMTP and use it instead of ours (smtp.eznettools.com).
|
|
|
Email Address:
|
|
|
Incoming POP3 Mail Server:
|
|
|
Outgoing SMTP Mail Server:
|
smtp.eznettools.net
|
|
Email Account Name:
|
|
|
|
The information above is generic. You will need to enter your own information. To find this information, click here and pay special attention to the "Get Info" section. Here you will be able to see what your domain is for the specific email(this will not always be a .com), the account name(ie. x300000a), and the password(if you have not already set it yourself).
|
|
|
While using a client e-mail program, such as outlook, that downloads the e-mail from your account with EZ-OnLineMail, you will want to have it set to remove the e-mail from the Ez-OnLineMail account completely. If you click the "Options" link at the top of Ez-OnLineMail then click the "Auto Response: Reply or Forward", which is the fourth link down on the right, you will find the "Keep a copy here?" option. Make sure this option is not checked. Also there usually is a setting on the client e-mail program for keeping a copy on the server that should not be checked.
|
|
|
|
|
|
|
1. Once you have opened Outlook Express, you will want to go to the Tools menu and select Accounts.
|
|
|
2. From the Accounts window you will want to click the New button.
|
|
|
3. On the "Your Name" window enter the name you will want people to see when they look at email from you. Click the next button in the bottom right.
|
|
|
4. On the "Internet E-mail Address" page enter your e-mail address. (ie. ). Click the next button.
|
|
|
|
5. On the Email Servers Name page select POP for your incoming mail server type. Enter in "mail.yourdomain.com" for your Incoming Mail Server. Your domain will be either your domain, or eznettools.net. Enter "smtp.eznettools.net" for your Outgoing Mail Server. Click the next button.
|
|
|
|
6. In the "Internet Mail Logon" page enter in your email account name. This is your x account number with a letter at the end(ie. , to find this account name click here, and pay special attention to the Get Info section.) USE A LOWER CASE "x"! You can also enter in your password and have it remember it so you don't have to retype it in every time you log in. Click the next button.
|
|
|
|
7. Now enter the display name for the e-mail account and check the box that adds the account to the "Send & Receive All". You can now click Finish.
|
|
|
|
8. Select the new e-mail account then click on the Edit button.
|
|
|
|
9. In this window, the settings for the account that was just created can be edited. Under Sending mail, click on the advanced sending options.
|
|
|
|
10. Check the "SMTP server requires authentication" and the "Use same settings as incoming mail server".
|
|
|
|
11. Close the advanced sending options window. Click OK on the Edit Account window. You are now ready to start sending and receiving e-mail in Outlook Express.
|
|
12. To remove the e-mails off the server make sure to uncheck the "Leave a copy of each message on the server" option. This is optional and if you use your EZ-OnLineMail account interface then you might not want to do this.
|
|
|
|
|
